|
|
|
我CPU是AMD A64 3200+% f) [9 m' f- ~
主板是技嘉GA-K8NF-94 V( R' h' r5 e3 r$ j, N
这是BIOS里的选项
g' J) V" f* g
; x9 O j i" S& G% T) z+ q* JHT Frequency ratio [auto,1X,1.5X,2X,2.5X,3X,4X,5X]
9 C k2 I0 O8 j/ kCPU FREQUENCY (CPU外频调节）1 F- o. e5 T2 G3 b# C# q% L2 K' w8 s3 H% h
K8 CPU CLOCK RATIO (CPU倍频调节）
& Q& O$ G* `; N) r1 c' ]Current DDR Speed 400 (不可调节）. m" }7 |7 R) k7 y& u
DDR Clock/Timing Made [auto,manual]" Y( o% `. R$ f+ ]% N1 ?2 V: p
CPU/DDR clock Radio [2/1,2/1.33,2/1.66,2/1.83,2/2,2/2.16,2/2.33,2/2.5]
( N" P$ r. j1 n" {/ N: wDDR speed 400 (不可调节）; R8 e- q, w, I6 X1 F. t
DDR Timing [AUTO,Manual]
* Y9 }7 I. G5 Q9 y) ^ ICAS# Latency(tcl) [1.5,2,2.5,3]
5 r6 u8 ?2 j9 ]9 P- n1 c1 ~/ ^Min RAS# active tine(tras) [auto,5T,6T,7T,8T,9T,10T,11T,12T,13T,14T,15T]默认为8T6 k p* B; s% k+ ~& B! @- b
RAS# to CAS# delay(trcd) [auto,2T,3T,4T,5T,6T,7T]默认为4T# h# N+ x- @ {( n' N! Q4 J/ w
Row precharge time(trp) [auto,2T,3T,4T,5T,6T,7T]默认为4T2 m+ k# Z p! P3 L) N3 ~- @
Row to row delay(Trrd) [auto,2T,3T,4T]默认为2T" O: v8 J6 R# T8 W
Row cycle time(Trc) [7T,8T,9T,10T,11T,12T,13T,14T,15T,16T,17T,17T,19T,20T,21T,22T]默认为 11T4 {# M( N1 S5 t* | A
Row retresh cyc time(trfc) [9T,10T,11T,12T,13T,14T,15T,16T,17T,17T,19T,20T,21T,22T,23T,24T]默认为14T
1 `; |0 H! @2 y" P: H/ {Read-to-write time(Trwt) [auto,1T,2T,3T,4T,5T]默认为4T% ]1 q# {7 d, X2 ]7 a* a
Write Recovery Time(Twr) [2 bus clock,3 bus clock]默认为3 bus clock
% A. `- Z: @/ u0 jWrite-to-read Delay(Twtr) [1 bus clock,2 bus clock]默认为2 bus clock9 I5 R( e; i4 x# g |/ ~! c( @
Refresh Rate(tref) [100MHZ 15.6us,133MHZ 15.6us,166MHZ 15.6us,200MHZ 15.6us,100MHZ 7.8us,133MHZ 7.8us,166MHZ 7.8us,200MHZ 7.8us,100MHZ 3.9us,133MHZ 3.9us,166MHZ 3.9us,200MHZ 3.9us]
% y: D/ p3 w: j. |默认为200MHZ 7.8us
y6 O9 d% u2 M+ PRead Preamble value [2ns,2.5ns,3ns,3.5ns,4ns,4.5ns,5ns,5.5ns,6ns,6.5s,7ns,7.5ns,8ns,8.5ns,9ns,9.5ns] 默认为5.5ns& B4 J! h1 o4 ~ ]$ [5 ?& {! a$ _
Async Latency value [2ns,3ns,4ns,5ns,6ns,7ns,8ns,9ns,10ns,11s]默认为7ns
1 ?" R) f" y( UCPU Spread spectrum [Disabled,center spread]
9 U6 P0 Q3 K% f* G- pPCIE clock [100-150MHZ]
+ X% Z3 B9 F; t& C, s/ I8 GRobust Graphics Booster [auto,fast,turbo]
) }) j! a. b1 O5 v6 t# X自己超了N次都超不成，后来用技嘉的那个超频软件在XP下能超，但我还是想通过调BOIS超。我该怎么设置？5 C! e' U( }- ?& w* j E# p- i& ?9 M7 h- \
1 ~0 f+ f8 _- ]& a4 |0 e' F/ r- L |
|
雷达卡
发表于 2007-1-23 18:30:56
提升卡
抢沙发